PIC18F2410-I/ML【PDF 155/234 页】IC PIC MCU FLASH 8KX16 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3844

151页 152页 153页 154页 [155页]156页 157页 158页 159页

2009 Microchip Technology Inc.

DS39636D-page 29

PIC18F2X1X/4X1X

REGISTER 2-1:

OSCTUNE: OSCILLATOR TUNING REGISTER

2.6.5.1

Compensating with the USART

An adjustment may be required when the USART

begins to generate framing errors or receives data with

errors while in Asynchronous mode. Framing errors

indicate that the device clock frequency is too high; to

adjust for this, decrement the value in OSCTUNE to

reduce the clock frequency. On the other hand, errors

in data may suggest that the clock speed is too low; to

compensate, increment OSCTUNE to increase the

clock frequency.

2.6.5.2

Compensating with the Timers

This technique compares device clock speed to some

reference clock. Two timers may be used; one timer is

clocked by the peripheral clock, while the other is

clocked by a fixed reference source, such as the

Timer1 oscillator.

Both timers are cleared, but the timer clocked by the

reference generates interrupts. When an interrupt

occurs, the internally clocked timer is read and both

timers are cleared. If the internally clocked timer value

is greater than expected, then the internal oscillator

block is running too fast. To adjust for this, decrement

the OSCTUNE register.

2.6.5.3

Compensating with the CCP Module

in Capture Mode

A CCP module can use free running Timer1 (or

Timer3), clocked by the internal oscillator block and an

external event with a known period (i.e., AC power

frequency). The time of the first event is captured in the

CCPRxH:CCPRxL registers and is recorded for use

later. When the second event causes a capture, the

time of the first event is subtracted from the time of the

second event. Since the period of the external event is

known, the time difference between events can be

calculated.

If the measured time is much greater than the calcu-

lated time, the internal oscillator block is running too

fast; to compensate, decrement the OSCTUNE register.

If the measured time is much less than the calculated

time, the internal oscillator block is running too slow; to

compensate, increment the OSCTUNE register.

R/W-0

R/W-0(1)

U-0

R/W-0

INTSRC

PLLEN(1)

—

TUN4

TUN3

TUN2

TUN1

TUN0

bit 7

bit 0

bit 7

INTSRC: Internal Oscillator Low-Frequency Source Select bit

1 = 31.25 kHz device clock derived from 8 MHz INTOSC source (divide-by-256 enabled)

0 = 31 kHz device clock derived directly from INTRC internal oscillator

bit 6

PLLEN: Frequency Multiplier PLL for INTOSC Enable bit(1)

1 = PLL enabled for INTOSC (4 MHz and 8 MHz only)

0 = PLL disabled

Note 1: Available only in certain oscillator configurations; otherwise, this bit is unavailable

and reads as ‘0’. See Section 2.6.4 “PLL in INTOSC Modes” for details.

bit 5

Unimplemented: Read as ‘0’

bit 4-0

TUN4:TUN0: Frequency Tuning bits

01111 = Maximum frequency

00001

00000 = Center frequency. Oscillator module is running at the calibrated frequency.

11111

10000 = Minimum frequency

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式